Eagle Jobs

36 were found based on your criteria

  • Fixed-Price – Est. Budget: $100.00 Posted
    This job is to create a BRD Eagle file I can use to generate gerber files for PCB mfr. Maximum board size is 9cm x 4.5cm. Two sided PCB, no internal layers. Bottom is mostly GND plane (under LED power drivers). Naturally, needs to be with soldermask layers in Eagle. I do not need schematics, only brd file. It drives up to 5 LED channels. One channel at 3A, 4 channels as 1A. It contains simple input protection, one ...
  • Fixed-Price – Est. Budget: $50.00 Posted
    Create a small board (in Eagle) that can be used by PCB manufacturer to make the boards. It uses one AN30888A SSOP16 LED driver and ATTiny85 MCU for PWM. MCU is powered by AN30888. Components will be hand soldered so there is no need for tight tolerances. Some components do not have size specified, use common sense. Schematic is attached. External input is by two buttons and a temperature sensor, so those need some soldering pads. This is just a ...
  • Hourly – Less than 1 week – Less than 10 hrs/week – Posted
    I am developing a little Arduino Project. I need somebody to design 2 pcb , finish my programs, and assist me in general. The project includes some RF communication, so workers who have experience on that are welcome PCB creation using free software. Fritzing preferably. High communication skills is a must
  • Fixed-Price – Est. Budget: $40.00 Posted
    I have a simple Altium pcb project (schematic with linked PCB) for which I would like to have an equivalent working Eagle project (schematic + pcb, with full forward/back annotation working). I have already exported the pcb from Altium to Eagle, created a library for the parts and manually re-drawn the schematic. But the schematic is not linking yet to the pcb in Eagle. Upon further investigation it seems that the pcb in Eagle has a some unconnected signals, although ...
  • Fixed-Price – Est. Budget: $250.00 Posted
    Design 2 PCBs from scratch and review and finish the layout of a 3rd PCB. See attached files for more details. Deliverables will be 3 sets of .sch and .brd files (1 set for each board) and a BOM in Excel for parts from either Digikey or Mouser.com. I have Eagle 6.3 and need to be able to look at them in Eagle. If you're using a different program please don't bid on the project.
  • Fixed-Price – Est. Budget: $100.00 Posted
    I need an electronic engineer to design driver for BLDC Motor. Motor is using Hall Sensors. Our input voltage to driver will be wide from 10.5v-28v and the motor is rated at 36v and maximum 1.2A. We need to run motor at maximum 1200rpm and speed control to reduce rpm. You have to design PCB Layout, Schematic and if need programming so you have to do this. You make the Gerber & BOM for production. We need a variable ...
  • Fixed-Price – Est. Budget: $60.00 Posted
    We have a very simple PCB that need to be reviewed before manufacturing. The PCB has two layer, few pins, resistance and a single IC; its complexity can be described as "trivial". The candidate should work TOGETHER with us (using Skype and a remote desktop software) to review the current design using EagleCAD, in particular the layout. We estimate the task will take 3 hous at most. Assignment must be accomplished as soon as possible. Please provide some samples of ...
  • Fixed-Price – Est. Budget: $1,000.00 Posted
    Hello, basically the project is to create the electronics to make a complete daft punk led display like in the video shown below but before you watch it, keep in mind that i am only trying to complete the silver helmet. http://www.youtube.com/watch?v=2SPN2pJThM0 ok here are the specs on it: 1.) the front is a 11x40 led matrix, so that means there are 11 leds going up and 40 going across. and each led is ...
loading