Eagle Jobs

10 were found based on your criteria

  • Hourly – Less than 1 month – Less than 10 hrs/week – Posted
    The specif of program is this: PCB in connect to one phototransistor PCB must comunicate when ( DD/MM/YYYY HH:MM ) the phototransistor send signal direct to one field of database sql or other folder we agree. I need a first release very simple C program install this in my PCB OpenPicus. If the collaboration start I need to grow this program every week. Reply to question BELOW. How many hours do you think to do this ?
  • Fixed-Price – Est. Budget: $500.00 Posted
    We need the gerber files for a dummy PCB which will be used in a hand-soldering training courses. The job consists of creating the PCB project based on the drawings we will provide you with a software of your choice. We need the gerber files for PCB physical production. The job complexity is extremely low, the PCB does not need to be functional.
  • Fixed-Price – Est. Budget: $250.00 Posted
    Hello, i am looking for Electronics Engineer to do some work on an open source sensor board: http://www.flexibity.com/ Code: https://github.com/Flexibity/shields/ this board is designed with wireless or usb, I am interested in the Wireless thap version. here is the modifications i need: 1- Make the Board Round 2- remove the aaa battery pins and place a pin for a rechargable battery: http://www.jayconsystems.com/media/catalog/product/cache/1/image/800x600/040ec09b1e35df139433887a97daa66f ...
  • Fixed-Price – Est. Budget: $150.00 Posted
    Hello, i am looking for Electronics Engineer to do some modification on USB Weather board From Sparkfun ( https://www.sparkfun.com/products/10586 ) this board is open source. here is the modifications i need: 1- Make the Board Round (curently its rectangular ) 2-Try to make it a bit smaller btw 5 to 6 cm in Diameter 3- at the moment the USB Board supports Xbee Bluetooth, i want to replace that witth USB Bluetooth dongle. 4-Modify the Firmware accordingly based ...
  • Fixed-Price – Est. Budget: $30.00 Posted
    I have a schematic and pcb layout done in altium i need updated. we are changing the current atmel at32uc3a464s micro to a atmel at32uc3a3128s. differences are the current is bga100, new is bga144. but the micros are both from same series so most pins remain the same. I also want to make 2-3 very minor component changes, ie replace diodes with cheaper/better solution, maybe mosfet ?? the current board is 6 layer, and has no nested vias. the new ...
  • Hourly – Less than 1 month – Less than 10 hrs/week – Posted
    Hi, I am about to start a new project based on the xmega processor from Atmel. I require some advise on what processor I should be using for my project and also some initial work on the schematic to get the basic building blocks of the circuit created: PSU for xmega (24v or 12v power source) Xmega + supporting components JTAG interface Then I will also require some advice on driving around 40 bi color LEDs (red/green), plus another 10 ...
  • Fixed-Price – Est. Budget: $200.00 Posted
    I have a simple project I need a schematic and pcb designed. I actually have the sch partially finished in altium from a previous developer that was not able to finish it. I would prefer the project was done in Eagle, but altium will be fine. the project uses an AT32UC3A464S micro and only has a few added components, ie usb, sd card, 5 buttons, 3 tricolor led, 2 batteries, 6 gpio pads, and jtag, very simple. I will provide ...
  • Fixed-Price – Est. Budget: $200.00 Posted
    I have a simple project I need a schematic and pcb designed. I actually have the sch partially finished in altium from a previous developer that was not able to finish it. I would prefer the project was done in Eagle, but altium will be fine. the project uses an AT32UC3A464S micro and only has a few added components, ie usb, sd card, 5 buttons, 3 tricolor led, 2 batteries, 6 gpio pads, and jtag, very simple. I will provide ...
  • Fixed-Price – Est. Budget: $200.00 Posted
    I have a simple project I need a schematic and pcb designed. I actually have the sch partially finished in altium from a previous developer that was not able to finish it. I would prefer the project was done in Eagle, but altium will be fine. the project uses an AT32UC3A464S micro and only has a few added components, ie usb, sd card, 5 buttons, 3 tricolor led, 2 batteries, 6 gpio pads, and jtag, very simple. I will provide ...
  • Fixed-Price – Est. Budget: $200.00 Posted
    I have a simple project I need a schematic and pcb designed. I actually have the sch mostly finished in altium from a previous developer that was not able to finish it. I would prefer the project was done in Eagle, but altium will be fine. the project uses an AT32UC3A464S micro and only has a few added components, ie usb, sd card, 5 buttons, 3 tricolor led, 2 batteries, 6 gpio pads, and jtag, very simple. I will provide ...
loading