Eagle Jobs

19 were found based on your criteria

  • Fixed-Price – Est. Budget: $60.00 Posted
    Looking for a circuit designer who can design a circuit that will switch to battery when voltage from solar cell drops below 2.5 volts. Additionally output power must not exceed 3.3v. Input battery voltage will not exceed 3.6v and input from the solar panel will not exceed 6.6 volts. The device that this will feed will normally draw 0.5 – 1.5 mA with regular spikes to 15 mA. Maximum draw is 20mA. The specs on ...
  • Fixed-Price – Est. Budget: $200.00 Posted
    I am looking for someone with PCB Design experience as well as Arduino programming experience. I want to design a 2.4ghz RC Transmitter & Receiver setup. The transmitter will be enclosed with a 3D printed enclosure as well as receiver. I need someone to design the PCB schematic as well as help build it with arduino + program it. A few features that the controller will have are the following: - Lipo battery pack for charging - Can be charged via USB - small ...
  • Fixed-Price – Est. Budget: $100.00 Posted
    Using the schematic, CAD dimensions and gerber files that will be provided, convert the simple design to Cadsoft Eagle files. Library should include: Devices Package Symbols Final project will include Eagle Schematic, PCB Board Layout and Gerber Files. All components must be properly labeled in schematic and on board. All engineering notes on schematic should be duplicated into Eagle schematics. All part numbers and components must match original schematic. Use of standard electronic symbols and correct part packages required. Neat ...
  • Fixed-Price – Est. Budget: $100.00 Posted
    This job is to create a BRD Eagle file I can use to generate gerber files for PCB mfr. Maximum board size is 9cm x 4.5cm. Two sided PCB, no internal layers. Bottom is mostly GND plane (under LED power drivers). Naturally, needs to be with soldermask layers in Eagle. I do not need schematics, only brd file. It drives up to 5 LED channels. One channel at 3A, 4 channels as 1A. It contains simple input protection, one ...
  • Fixed-Price – Est. Budget: $100.00 Posted
    We need a sensorless motor control by using ic L6230. Please see the attached Datasheet of L6230 and make the schematics design using a microcontroller to control the L6230. And make the programming for microcontroller such as L6230 can be used to drive a BLDC Sensorless motor. Also we need one output signal from MCU before it starts motor such as we can power on external power supply for motor. Also we need one button for Start, Stop, Speed Up ...
  • Hourly – 1 to 3 months – 10-30 hrs/week – Posted
    Hi, Please respond with the first line being your name. i am looking for somebody that can design PCB boards for us, we only want good quality designs, we have a few projects to start immediately, please submit some work you have currently completed also, most of our work interfaces with smart phones with php etc
  • Fixed-Price – Est. Budget: $50.00 Posted
    Create a small board (in Eagle) that can be used by PCB manufacturer to make the boards. It uses one AN30888A SSOP16 LED driver and ATTiny85 MCU for PWM. MCU is powered by AN30888. Components will be hand soldered so there is no need for tight tolerances. Some components do not have size specified, use common sense. Schematic is attached. External input is by two buttons and a temperature sensor, so those need some soldering pads. This is just a ...
  • Fixed-Price – Est. Budget: $40.00 Posted
    I have a simple Altium pcb project (schematic with linked PCB) for which I would like to have an equivalent working Eagle project (schematic + pcb, with full forward/back annotation working). I have already exported the pcb from Altium to Eagle, created a library for the parts and manually re-drawn the schematic. But the schematic is not linking yet to the pcb in Eagle. Upon further investigation it seems that the pcb in Eagle has a some unconnected signals, although ...
  • Fixed-Price – Est. Budget: $100.00 Posted
    I need an electronic engineer to design driver for BLDC Motor. Motor is using Hall Sensors. Our input voltage to driver will be wide from 10.5v-28v and the motor is rated at 36v and maximum 1.2A. We need to run motor at maximum 1200rpm and speed control to reduce rpm. You have to design PCB Layout, Schematic and if need programming so you have to do this. You make the Gerber & BOM for production. We need a variable ...
  • Fixed-Price – Est. Budget: $1,000.00 Posted
    Hello, basically the project is to create the electronics to make a complete daft punk led display like in the video shown below but before you watch it, keep in mind that i am only trying to complete the silver helmet. http://www.youtube.com/watch?v=2SPN2pJThM0 ok here are the specs on it: 1.) the front is a 11x40 led matrix, so that means there are 11 leds going up and 40 going across. and each led is ...
loading