Electrical Drawing Jobs

31 were found based on your criteria

  • Fixed-Price – Est. Budget: $100.00 Posted
    DESCRIPTION We need a freelancer to modify the current electrical circuit to use only hard components and no logic board. The components for the assembly components need to cost below $10 all together. DELIVERABLES: 1. Revised Wiring diagram/schematic with a Bill of materials(BOM) containing the catalogue numbers of the components the freelancer specified and where we can purchase them 2.CAD files for all items on the BOM(or cutsheets, we just need to be able to put ...
  • Fixed-Price – Est. Budget: $1,000.00 Posted
    There a couple of these on the market but none of them are affordable. Here are some of the requirements: 1. Make at least 20 blocks per day. 2. Meet UL standards 3. Parts to make this need to cost less $1000. 4. Be able to make round or square blocks of ice. Most of them use glycol. Here are some examples http://www.1-800-shaved-ice.com/spblicemaupt.html http://www.1-800-shaved-ice.com/404-14-spb.html Also I would like to open ...
  • Hourly – 1 to 3 months – 10-30 hrs/week – Posted
    Work Description: Electrical termination of house in the beach of Valencia, Spain (Albufera) http://goo.gl/n81W39 The house is in the final stage of construction and we intent to move in in 2 months. The electrical installation and intelligent house installation (domotica). The house is painted but have the installation of electrical sockets missing. - Light Design - KNX installation based on ABB outputs and Gira input - Electrical termination. All cabels are in place and all light points are installed. Deliveries ...
  • Hourly – 3 to 6 months – 10-30 hrs/week – Posted
    Electrical engineer is required to review electrical drawings prior to construction and validate that the loads are sufficient for the equipment, make necessary amendments on main distribution panels, sub distribution panels, and cables where necessary. Scope may be extended to other electrical design works as necessary.
  • Hourly – 1 to 3 months – Less than 10 hrs/week – Posted
    Looking to build a micro controller + display for a resistance fitness machine, The machine consists of few elastic tubes that when are pulled by the trainee create resistance and help to develop muscles. The resistance of each band is known, The controller should calculate and provide all statistics regarding the resistance used during workout, over time and statistics measures per user. Sensors should measure the number of time each band was pulled. Data can be transmitted via Bluetooth to a ...
  • Hourly – Less than 1 month – 30+ hrs/week – Posted
    The first in a new line of robotic lawn mowers is being developed. I can't say too much in an open forum but the piece of work is about taking the requirements for the mower and translating that into a PCB Schematic. If this is done well there is also the piece of work of turning the schematic into an actual PCB design so please only apply for this job if you can do both parts.
  • Hourly – Less than 1 week – 10-30 hrs/week – Posted
    We have to change a model for a thermostat that was created in solidworks. The next items should been done this week: • The size of the housing has to be shorter, the space between the PIR and the solar must be limited with 2 cm • The mark on the knob should be changed into 5 signs positions and the there must be a mark on the housing that will set the position. The middle position is the most used one ...
  • Fixed-Price – Est. Budget: $25.00 Posted
    We are a small charity designing a small "caravan" to be towed by a bicycle (it is a small portable clinic). The caravan needs to be solar powered and store the solar power in batteries. It must be small and light and efficient. We need the electrical diagram / drawing done by someone who knows his "stuff" about electrical engineering. Attached is a very basic drawing of what we have designed. OUTPUTS REQUIRED BY YOU: 1 x circuit design (line drawing ...
loading