Electrical engineering Jobs

41 were found based on your criteria

  • Fixed-Price – Est. Budget: $10.00 Posted
    Need someone help me to edit my old report for my new project. I have doc temple file ready just need edit it, take 30-60 min can completed this report. $10 budget. Need doc file in 24 hour. Attached is sample report for reference, I only need electrical section about 20-30 pages Need to see your report sample, before hire
  • Fixed-Price – Est. Budget: $10.00 Posted
    Need a electrical engineer to draft existing electrical panel, panel schedule, power plan, single line diagram. $10 budget . need drawing completed in CAD file within 24 hr. If you like to take this project, please send your electrical drawing sample with your information include information below email direct contact phone number skype number (freelancer need to be able communicate in English)
  • Fixed-Price – Est. Budget: $200.00 Posted
    the power supply board, it has to be fully re-designed with following specs; 1 The power supply is a separate PCB with input range from 3VDC to 70VDC 2 Primary Power Supply INPUT: 28V nominal OUTPUT 1: 5V @ 4 A (peak up to 7A) (IRIDIUM + THURAYA + OMAP) OUTPUT 2: 3.3V @ 2 A (peak up to 3A) (DECT + LOGIC BOARD) OUTPUT 3: 3.7V @ 1 A (peak up to 1.5A) (TETRA+GSM) OUTPUT 4: 30V @ 1A max More details ...
  • Fixed-Price – Est. Budget: $20.00 Posted
    hello, i need some help connecting 2 Encoder Motors with drivers to be controlled by arduino.. here is the hardware i have: 2x GB37Y3530 http://www.dfrobot.com/index.php?route=product/product&product_id=633#.U75q6Y1dU0_ http://www.dfrobot.com/image/data/FIT0185/64CPR-encoder.jpg 2x L298N http://www.amazon.com/Bridge-Stepper-Driver-Controller-Module/dp/B008KYCDTY 1 X Arduino Uno SMD R2 your Task is to help me connect the 2 encoder motors to the drivers and then connect both using the ...
  • Fixed-Price – Est. Budget: $100.00 Posted
    I have a Arduino Mega2560 board connected to a 16x2 LCD screen. I also have a lithium battery connected to my Arduino by I2C 2-wire I would like to display battery capacitance I have datasheets for battery, it uses a Texas Instruments BQ3050 fuel gauge I also have Arduino sketches for similar projects and videos with wiring diagrams If this can be achieved, I have lots of other project with Arduino Sketches
  • Fixed-Price – Est. Budget: $25.00 Posted
    Hi All, I'm looking for some help designing a few small PCB layouts. My end goal is to have 4 independent wireless MEMS accelerometer boards that transmit data to a micro-controller board. The micro-controller also will have a bluetooth module so data can be output to a cell phone or laptop. The 3-axis accelerometers will be sampled somewhere in the frequency range of 1-2kHz (to accurately measure vibration). I should note that, as a mechanical engineer, I have minimal ...
  • Fixed-Price – Est. Budget: $1,000.00 Posted
    We are looking for a contractor to help us with simulations for a PCB antenna. HANDS ON EXPERIENCE WITH IE3D IS A MUST. The work includes the following steps: 1. Antenna simulation for free space (Base Design) -- simulate the return loss and radiation pattern and prove that the simulation is consistent with the reference design. DELIVERABLE 1: Charts, graphs, etc showing that the simulation for the Basic Design is consistent with the reference design from the manufacturer and provide the ...
  • Fixed-Price – Est. Budget: $150.00 Posted
    i want to make mat lab code for paper. i want you to make matlab code for this paper (Comparison of Fractional Frequency Reuse Approaches in the OFDMA Cellular Down link) to gain the same result like in the paper. then make sectorization to the cell and gain new results. the sectorization will do at strict ffr only and the gain new results.i want sectorization like that photo attached
  • Fixed-Price – Est. Budget: $150.00 Posted
    Using the LTC3852 IC and the reference design from the datasheet: http://cds.linear.com/docs/en/datasheet/3833f.pdf Create a schematic and pcb board layout in Eagle for a 5VDC, 10AMP power supply.. Input Voltage: 12VDC Input Connector: 5.5X2.5mm barrel (surface mount) Output: +5VDC @ 10 AMPS Output Connector: Large solder thru holes. Board size up to 75MM X 75MM Single red LED power indicator (0805 SMT) Although this project is a simple reference design duplication, it ...
loading