Embedded Systems Jobs

12 were found based on your criteria

  • Hourly – 1 to 3 months – 30+ hrs/week – Posted
    Along with your hourly rate, please provide an estimate of how many hours the project will take. The project is for a small consumer product that will use motion control to activate a light. The heart of the project is a Printed Circuit Board with a Microcontroller (MCU) and an Accelerometer (ACCEL). The device will need to be configured to run on the lowest power possible, with the device going into low power, or sleep mode in-between each MCU cycle ...
  • Hourly – Less than 1 month – 30+ hrs/week – Posted
    We would like to develop a System that would read OCR data from Cameras Video stream and store the data into a database for analysis and real time reporting. The systems should be able to capture real time data from the 3 camera and also analyse it alongside recorded and stored data and give defined inputs. The cameras are just checking printing paper with printed serial number & Pin numbers that are being printed within a factory production line. The size ...
  • Hourly – 1 to 3 months – 10-30 hrs/week – Posted
    I am looking for help to produce few, simple connected items to my IOT platform. You will be using Arduino and X-Bee parts and sketches. The first three projects will be 1. A wireless heart rate monitor and 2. Xbee location sensors emitters and receivers 3. Tension sensor You will create and miniaturize prototype and work with our developers to integrate in to network and visualize output. You will be paid per project and you will be residing in the ...
  • Hourly – Less than 1 week – 10-30 hrs/week – Posted
    I need to design an embedded system that can generate 12 different audio-rate squarewaves (between 20 Hz and 20kHz). The squarewave peak-to-peak amplitudes must be at least 3.3 Volts. 5 Volt amplitudes are also acceptable. The GPIO pins of most microcontrollers will be able to produce these signals. We need real-time control of each squarewave, so that we can turn any signal ON or OFF at any time... Later in the project design, I plan use MIDI messages to ...
  • Hourly – 1 to 3 months – 10-30 hrs/week – Posted
    We require an electronics engineer who can join a project team in the development of a new electronic embedded device. This device will incorporate in its electronic design the following; - Micro controller - WiFi - RFID - Other signal inputs and output devices The successful contractor must be skilled in - Electronics Circuit development - Firmware Development - WiFi circuits and circuit integration - Electronic component selection and costing - PCB Design ON and during completion of this project, all documentation, schematics, drawings, code, models and information required ...
  • Hourly – More than 6 months – 10-30 hrs/week – Posted
    Atmel AVR microcontroller software programming, software QC, software test. Software programming and some hardware design for Atmel AVR based embedded product. The project will be to finish a previously started project, much of the work on this project has been done. Must be able to quickly and efficiently program in C/ C++/ and assembly code for Atmel AVR microprocessors. Complete specifications, software flow charts, and product samples will be available to the programmer. Limited hardware PCB design experience required. Must ...
  • Hourly – Less than 1 month – Less than 10 hrs/week – Posted
    Looking to create an application library for a specific Zigbee RF4CE USB module provided by Texas Instruments, to remotely control a cable Set Top Box. The application library will require knowledge of working with TI's IDE along with embedded SoCs. The candidate of choosing for this job will be supplied a remote system where the dongle and target device will be located. It is expected that the candidate also develop a sample utility application that shows the basic functionality ...
  • Fixed-Price – Est. Budget: $150.00 Posted
    The project is to capture and records Wi-Fi these signals for analysis. Using a raspberry or open_mesh access point OM2P-LC, we record pings and send them to our cloud-based systems. the project is to develop - Raspberry Module - OpenMesh OM2P-LC module
  • Hourly – Less than 1 month – 10-30 hrs/week – Posted
    I am looking for an embedded C developer with experience in AVR as well as embedded linux. The project is to incorporate the sensors below to either ARM11 running embedded linux and/or Atmel 2560 Accelerometer/gyroscope RFID Bluetooth fingerprint scanner zigbee
  • Hourly – 1 to 3 months – Less than 10 hrs/week – Posted
    Embedded software developer needed with good experience in ARM cortex STM32F205XXX This is what we need: Firmware specification and change. We need to add Bluetooth LE cc2540 from TI Tests of firmware to be integrated: Fingerprint sensor library and USB device driver library. Firmware integration and testing Documentation of USB API protocol and all firmware integraded This is done for our Generation ONE device, now we need to update and change for Generation TWO. The work is based upon the ...
loading