PCB Design Jobs

25 were found based on your criteria

  • Fixed-Price – Est. Budget: $200.00 Posted
    the power supply board, it has to be fully re-designed with following specs; 1 The power supply is a separate PCB with input range from 3VDC to 70VDC 2 Primary Power Supply INPUT: 28V nominal OUTPUT 1: 5V @ 4 A (peak up to 7A) (IRIDIUM + THURAYA + OMAP) OUTPUT 2: 3.3V @ 2 A (peak up to 3A) (DECT + LOGIC BOARD) OUTPUT 3: 3.7V @ 1 A (peak up to 1.5A) (TETRA+GSM) OUTPUT 4: 30V @ 1A max More details ...
  • Hourly – 1 to 3 months – 30+ hrs/week – Posted
    Along with your hourly rate, please provide an estimate of how many hours the project will take. The project is for a small consumer product that will use motion control to activate a light. The heart of the project is a Printed Circuit Board with a Microcontroller (MCU) and an Accelerometer (ACCEL). The device will need to be configured to run on the lowest power possible, with the device going into low power, or sleep mode in-between each MCU cycle ...
  • Fixed-Price – Est. Budget: $25.00 Posted
    I am looking for someone who can produce the eagle files need to have some PCB boards manufactured. I have the Schematic, but will need the eagle bit done. I intend to use hackvana who's specification can be found in the link before for the board specifications. But can you a different supplier if recommended. The curcuit is simple, 1 IC Chip, 2 LED's 2 Capacitors, 2 variable resitors and 2 resistors. https://docs.google.com/document/d ...
  • Fixed-Price – Est. Budget: $25.00 Posted
    Hi All, I'm looking for some help designing a few small PCB layouts. My end goal is to have 4 independent wireless MEMS accelerometer boards that transmit data to a micro-controller board. The micro-controller also will have a bluetooth module so data can be output to a cell phone or laptop. The 3-axis accelerometers will be sampled somewhere in the frequency range of 1-2kHz (to accurately measure vibration). I should note that, as a mechanical engineer, I have minimal ...
  • Hourly – 1 to 3 months – 10-30 hrs/week – Posted
    We require an electronics engineer who can join a project team in the development of a new electronic embedded device. This device will incorporate in its electronic design the following; - Micro controller - WiFi - RFID - Other signal inputs and output devices The successful contractor must be skilled in - Electronics Circuit development - Firmware Development - WiFi circuits and circuit integration - Electronic component selection and costing - PCB Design ON and during completion of this project, all documentation, schematics, drawings, code, models and information required ...
  • Fixed-Price – Est. Budget: $150.00 Posted
    Using the LTC3852 IC and the reference design from the datasheet: http://cds.linear.com/docs/en/datasheet/3833f.pdf Create a schematic and pcb board layout in Eagle for a 5VDC, 10AMP power supply.. Input Voltage: 12VDC Input Connector: 5.5X2.5mm barrel (surface mount) Output: +5VDC @ 10 AMPS Output Connector: Large solder thru holes. Board size up to 75MM X 75MM Single red LED power indicator (0805 SMT) Although this project is a simple reference design duplication, it ...
  • Fixed-Price – Est. Budget: $60.00 Posted
    Create a parts library for the following two components: - Analog Devices SSM2306 Audio Amp http://www.analog.com/static/imported-files/data_sheets/SSM2306.pdf - Knowles Speaker-1115-3.5-sc-COBRA Speaker pad should allow for bidirectional (180 degree placement with same polarity on pins) http://media.digikey.com/pdf/Data%20Sheets/Knowles%20Acoustics%20PDFs/2403-260-00132.pdf Each part must include: Symbol Package Device Experienced PCB designers only.
  • Fixed-Price – Est. Budget: $500.00 Posted
    So I have a concept project I am working on. A small electronic device that I could really use some help with. I have some designs done in Proteus, and Gerber files, but its not yet completed. So I need someone willing to start from scratch and deliver gerber files. In short, the design has a 16 pin pcb connector, which pulls 12v dc power, outputs sound, outputs 5v usb charging power, not reading capabilities, to 2 usb females, and ...
loading