PCB Design Jobs

193 were found based on your criteria

  • Fixed-Price – Est. Budget: $200.00 Posted
    I am looking for someone with PCB Design experience as well as Arduino programming experience. I want to design a 2.4ghz RC Transmitter & Receiver setup. The transmitter will be enclosed with a 3D printed enclosure as well as receiver. I need someone to design the PCB schematic as well as help build it with arduino + program it. A few features that the controller will have are the following: - Lipo battery pack for charging - Can be charged via USB - small ...
  • Fixed-Price – Est. Budget: $50.00 Posted
    Hello, I have found a circuit board drawing online that I'd like to have made into a virtual breadboard using the software at http://www.virtualbreadboard.com, free to download. The circuit drawing I found was probably made in paint, there is no author to it, and hence no support. The original circuit was made with three levels where the designer soldered IC chips on top of each other. I don't want to do this. I just want ...
  • Fixed-Price – Est. Budget: $40.00 Posted
    I need a small daughterboard designed. It is very basic. PCB Size +- 3x3 to 5 x 5 cm (3x3 will be best if you can make the terminals fit. Terminals need to be1/2cm x 1/2 cm. Center of the board, a 8 pin IC socket The board redirects the following pins to (looking from the top): - Pins 8 and 4 (top) - Pins 7, 6 and 2 (left) - Pins 1 and 5 to the (bottom) and - Pins 3 to ...
  • Hourly – 1 to 3 months – Less than 10 hrs/week – Posted
    Hi There, I am the founder of a new wireless headphone company Hooke. www.hookeaudio.com Hooke are wireless headphones with a twist - they playback music AND capture 3D Audio. We're just about to complete our Kickstarter, where we've raised over $145,000. https://www.kickstarter.com/projects/124900576/hooke-wireless-3d-audio-headphones At the moment, the majority of the schematic entry and PCB part generation work has been completed. I need a very experienced engineer to layout the PCB. APPLICANT ...
  • Fixed-Price – Est. Budget: $100.00 Posted
    I need a device which is able to gather data from an accelerometer and a RFID reader. It should only activate when moving. If it moves, it should start transmitting a data stream, including the data from the accelerometer and the RFID reader via bluetooth to a connected bluetooth device. Thus I need the device to contain the following components: - Bluetooth Module - Accelerometer - RFID - Battery (needs charge indicator) The device should be able to read data from RFID-Sources within a ...
  • Fixed-Price – Est. Budget: $500.00 Posted
    We need a PCB designer to help us design a custom motherboard for a concept product. The board will be part of a HD network-camera (CCTV) video-recording device. The board will operate a LINUX OS and will have a number of key components physically installed on the board as listed below: 1) 16 x POE RJ-45 network jacks w/ status LED indicators 2) 1 x LAN/WAN RJ-45 network jack w/ status LED indicators 3) 1 x 4.0TB SATA ...
  • Hourly – Less than 1 month – Less than 10 hrs/week – Posted
    Currently, I have a prototype product that runs off an Arduino Uno, which controls two solenoids and 2 Mosfets. There are 2 analog potentiometer inputs, a push button, a microswitch and an LCD display. The prototype functions flawlessly and performs exactly how I want it, however, I want to add wireless communication (BT or WiFi) with an Android Device. Then have the Android device perform the functions of the 2 Pots and the push button as well as display the ...
  • Hourly – Less than 1 week – Less than 10 hrs/week – Posted
    To design a very high gain, multi-stage preamp with filters low signal 1-5 uV low freq 4- 46 hz low noise high gain preamp 50 -60 hz notch filter band pass filter 4- 46 hz gain 1000 to 10,000 Initially to design schematic circuit and PCB Build a breadboard version for our engineer to test Design PCB layout This job needs to be done urgently
  • Hourly – Less than 1 week – Less than 10 hrs/week – Posted
    I have created the schematic for a project that I am working on, but because I don't have a professional PCB layout software package I cannot build a board big enough. I have created the schematics in EAGLE and the basic layout of the board, I need someone add the additional components on a larger circuit board than I can create with hobbyist software. Prefer no more than 4 layer PCB, 2 layer if possible. Components on one side ...
  • Hourly – More than 6 months – Less than 10 hrs/week – Posted
    Layout Printed Circuit Designs based on existing schematics and/or rough sketch schematics. Must be very experienced in all aspects of PCB layout issues and have a minimum of 5 years on the job experience in laying our PCB's. Must have layout tools including PADS software. Must be available to work approximately 5 - 15 hours per week on a periodic basis, as needed.Immediate needs are required now.
loading